Engine

The goal when developing our new top mounted intercooler was to make it the very best aftermarket top mounted intercooler for the Forester.

We studied our competitors products and fixed all of the mistakes they have made...some of them major.

The most obvious error that every one of our competitors makes is not supplying their intercooler with proper ducting/shrouding to suit the increased size of the new intercooler. There is no point in installing a larger intercooler and leaving the factory under bonnet splitter/shroud in place. Here is the solution. A properly sized splitter/shroud to suit the application.

• Core Size: 490 x 193 x 90mm
• Silicone Y-Pipe
• Hood Splitter included

Increasing the intercooler surface area beyond that of the factory unit is all well and good but only if all of the ambient air is available to all of the upgrade intercooler so maximum heat exchange can take place. The answer here is of course a revised under bonnet duct.

The new Process West 04-09 Liberty GT Top Mount Intercooler addresses all of the above issues and it does it very well. Process West's new Top Mounted Intercooler is virtually a small front mounted intercooler mounted in the engine bay.

With a massive 400mm flow length (almost double the factory unit) and a not too thick 90mm bar and plate core an effective top mount is now here.

Details:

• Core Size: 400 x 198 x 90mm
• Strong & Durable Intercooler Hoses included
• Hood Splitter included

Process West 2015+ WRX TGV Deletes 

PLEASE NOTE: FUEL LINES AND INJECTORS ARE NOT SUPPLIED WITH THIS KIT.

Designed for the MY15+ FA20DIT WRX the Process West ‘DITTO’ (Direct Injection Tubular Original) compromises a mix of billet plenum and cast large bore runners to achieve the highest intake flow rates possible.  Over 12 months from initial design to testing on our own in-house WRX has allowed us to ensure not only guaranteed performance gains (see attached dyno sheet of a totally standard WRX with and without DITTO) but also perfect fitment. Note DITTO is a direct fit for Process West top and front mount intercooler equipped vehicles.* (see application notes below).

Power gains come from computer designed and tested internal plenum porting and an overall larger volume and greater runner capacity for optimal cylinder filling. Not only does DITTO offer these advantages but it is also part of our new ‘NO CEL’ product range that allows fitment to a totally standard vehicle with no Check Engine Light or Tuning required. Obviously even further improved results can be achieved in tuned versions of the FA20, with our experience showing the greater the power output, the greater the gains!

The Port Injection DITTO RACE version provides unmatched tuning flexibility in the form of an additional 4 port injector mounts. Designed to take any EV-14 specification fuel injector this delivers tuners the flexibility to add substantial extra amounts of fuel from an aftermarket ecu/injector driver to give a true 1000+hp worth of capacity. Whilst Process West don’t offer the computer hardware, we do deliver the functionality that highly tuned engines need.

*APPLICATION NOTES

Process West VERTICOOLER requires fitting kit – Part Number: PWIM007VFT HERE

Process West DITTO will directly fit with all front mount intercooler kits that use the stock inlet manifold.

Process West DITTO may require other brand (non-Process West) Top Mount Intercoolers have bracket modifications to fit.

For cars requiring even more power in the upper rev range the track version can be supplied with shorter billet TGV's (lower runner section). HERE

KPM  injectors are developed with the highest precision engineering. All KPM Fuel System products are of the highest quality, through premium manufacturing processes. Our fuel injectors are serialised and individually characterised to ensure the highest level of performance and reliability.

Upgrading the fuel injection is vital once modifications are made to increase horsepower. Giving more flexibility for tuning and is necessary once the limit of the factory injectors/fuel system is reached.

Theses injectors are suitable for mild – heavily modified vehicles. Allowing increased fuel flow and developed for performance tuning. The injectors are a complete, machined, flow tested set. Along with the injectors we provide the scaling data used for precise tuning.

Vehicle compatibility: 

• BRZ/86

Includes Injector Connecter Adaptors Where Required

Omni Power USA 2.5, 3, 4 & 5 Bar MAP (Manifold Absolute Pressure) sensors use state of the art bipolar op amp circuitry with thin film resistor networks built into each micro chip.

Pressure changes are calculated on a true linear 0-5 volt scale via a specially designed silicon pressure sensor that also compensates for temperature changes. The unique ability to compensate for temperature changes allows the Omni Power USA MAP sensor to remain a minimum of 99% accurate from 32 degrees F to 180 degrees F through out its range of scale.

With the true linear pressure vs. voltage scale there is never a need to re-tune at different altitudes as with other sensors. Competitors sensors on the market don't have true linear scaling which can cause your engine to go out of tune with elevation changes, often resulting in idle problems, poor drivability, and catastrophic engine damage. 

Key features:

• Cases are designed to withstand in excess of 130 PSI without leaking
• -40 to 260 degrees Fahrenheit temperature operating range
• Able to respond from 10% of the pressure scale to 90% of the pressure scale in .001 seconds (the fastest response time of any MAP sensor on the market).
• Automatic temperature compensation.
• True linear scaling for perfect drivability at all boost and vacuum levels.
• Compatible with all aftermarket engine management systems.
• Minimum of 99% accurate over full scale range under all conditions including temperature, altitude, and humidity changes.
• Allows smoother engine operation, higher boost levels, and better drivability than competitors turbo MAP sensors.
• Direct plug and play for an easy install and an OEM look. Dimensionally identical to the stock MAP sensor.
• Each sensor is hand assembled, pressure, and function checked in the USA for unparalleled quality control prior to shipping.

*Please note vehicle will require tuning after installation*

*Note: Older vehicles from 2001-2007 may experience diffuculty with tuning if using stock 16-Bit ECU. Check with your tuner that this product is right for you before purchasing*

Omni Power USA 3, 4 & 5 Bar MAP (Manifold Absolute Pressure) sensors use state of the art bipolar op amp circuitry with thin film resistor networks built into each micro chip.

Pressure changes are calculated on a true linear 0-5 volt scale via a specially designed silicon pressure sensor that also compensates for temperature changes. The unique ability to compensate for temperature changes allows the Omni Power USA 4 Bar MAP sensor to remain a minimum of 99% accurate from 32 degrees F to 180 degrees F through out its range of scale.

With the true linear pressure vs. voltage scale there is never a need to re-tune at different altitudes as with other sensors. Competitors sensors on the market don't have true linear scaling which can cause your engine to go out of tune with elevation changes, often resulting in idle problems, poor drivability, and catastrophic engine damage. 

Key features:

• Cases are designed to withstand in excess of 130 PSI without leaking
• -40 to 260 degrees Fahrenheit temperature operating range
• Able to respond from 10% of the pressure scale to 90% of the pressure scale in .001 seconds (the fastest response time of any MAP sensor on the market).
• Automatic temperature compensation.
• True linear scaling for perfect drivability at all boost and vacuum levels.
• Compatible with all aftermarket engine management systems.
• Minimum of 99% accurate over full scale range under all conditions including temperature, altitude, and humidity changes.
• Allows smoother engine operation, higher boost levels, and better drivability than competitors turbo MAP sensors.
• Direct plug and play for an easy install and an OEM look. Dimensionally identical to the stock MAP sensor.
• Each sensor is hand assembled, pressure, and function checked in the USA for unparalleled quality control prior to shipping.

*Please note vehicle will require tuning after installation*

Bosch ECO Wiper Blade Single 

Are your wiper blade arm assemblies all faded?

 Replace them now with these Bosch Blades!

Simply measure your old wiper blade and select the corresponding length below!

Bosch Aerotwin Wiper Blade Single 

Are your wiper blade arm assemblies all faded?

 Replace them now with these modern Bosch Blades!

Simply measure your old wiper blade and select the corresponding length below!

ACL Race Series Oil Pump

From the makers of ACL Engine Bearings comes a new line of high performance oil pumps Subaru applications.